sciencetech-blog

comments

Scientists have stumbled across an entirely new shape - while playing with elastic bands.

Harvard researchers were attempting to fabricate new springs for a project, and stumbled across an odd shape.

They were then able to recreate it in experiments where they stretched, joined, and then released rubber strips.

While setting out to fabricate new springs, a group of Harvard researchers stumbled upon a surprising discovery: the hemihelix, a shape rarely seen in nature. This image shows a helix (top), a hemihelix with one perversion marked by an arrow (middle), and a hemihelix with multiple perversions (bottom).

Once the team had spotted the odd shape, they were able to recreate it.

Complemented by numerical simulations and analysis of the process, the results appear in a paper published in the journal PLOS ONE.

Knowing precisely how to make the structures, predictably and consistently, may enable scientists to mimic the geometrical features in new molecules that could lead to possible advances in modern nanodevices, including sensors, resonators, and electromagnetic wave absorbers.

'Once you are able to fabricate these complex shapes and control them, the next step will be to see if they have unusual properties; for example, to look at their effect on the propagation of light,' said Katia Bertoldi, associate professor of applied mechanics at the Harvard School of Engineering and Applied Sciences (SEAS).

The shape that Bertoldi and colleagues at SEAS unexpectedly encountered is a hemihelix with multiple 'perversions.' Helices are three-dimensional structures; think of a corkscrew or a Slinky toy.

Hemihelices form when the direction in which the spiral turns—known as the chirality—changes periodically along the length.

The reversal in chirality is called a perversion.

How to make a hemihelix: Starting with two long elastomer strips of different lengths, the shorter one is stretched to the same length as the other. While the stretching force, P, is maintained, the two strips are joined side-by-side. Then, as the force is slowly released, the bi-strip twists

The team was trying to make two-dimensional springs by taking two strips of rubber material of different lengths and stretching the shorter one to reach the same length as the longer one and then sticking them together, explains David R. Clarke, Extended Tarr Family Professor of Materials at SEAS.

'We expected that these strips of material would just bend—maybe into a scroll.

'But what we discovered is that when we did that experiment we got a hemihelix and that it has a chirality that changes, constantly alternating from one side to another.'

Jia Liu, a graduate student in Bertoldi's group, tested differences in the aspect ratio—the width-to-height ratio of the rubber strips—and discovered that when a strip is very wide relative to its height, it produces a helix.

Further measurements revealed that there is a critical value of the aspect ratio at which the resulting shape transitions from a helix to a hemihelix with periodic reversals of chirality.

Other classes of materials would simply break when stretched to the mismatched strains that the polymers endured—likely the reason this behavior had never been observed before.

'We see deterministic growth from a two-dimensional state—two strips bonded together—to a three-dimensional state,' Liu says.

The researchers were experimenting with helices- three-dimensional structures seen in a corkscrew or a Slinky toy

'The actual number of perversions, the diameter, everything else about it is entirely prescribed.

'There is no randomness; it's fully deterministic. So if you make one hundred of these, they'll always perform exactly the same way.'

Bertoldi adds: 'From a mechanical point of view you can look at these as different springs with very different behavior.

'Some of them are very soft and then they stiffen up.

'Some are more linear.

'Simply by changing geometry, you can design this whole family of springs with very different behavior with predictable results.'

The team believe their findings provide important clues for how to fabricate a variety of three-dimensional shapes from flat parts.

'Intellectually, it's interesting—and we believe it is significant too,' Clarke says.

'There are a variety of complex shapes in nature that arise as a result of different growth rates.

'We stumbled quite by accident on a way to achieve fully deterministic manufacture of some three-dimensional objects.'